BALBOA | ELECTRONIC SPA CONTROLS | 54218-Z

BALBOA | ELECTRONIC SPA CONTROLS | 54218-Z

SPA CONTROL

*********************************************************************************************************************

THIS IS A BALBOA RETRO-FIT SPA CONTROL DESIGNED AS A COMPLETE
REPLACEMENT CONTROL

INCLUDES: (SEE BELOW FOR MORE DETAILED INFORMATION)
CONTROL WITH HEATER
SPASIDE CONTROL PANEL
SPASIDE CONTROL PANEL ADAPTER PLATE
SPASIDE CONTROL EXTRA LABEL
AMP CORDS
LIGHT HARNESS

*********************************************************************************************************************
SPECIAL NOTE - USING THE SYSTEM WITH A CIRCULATION PUMP

IF THIS IS BEING USED WITH A CIRCULATION PUMP AND THE CIRCULATION PUMP IS USED TO RUN THE HEATER,
THEN YOU MUST USE AN IRON MITE PUMP AS THE CIRCULATION PUMP.

YOU MUST HAVE A LEAST 20 GPM THRU THE HEATER TO ACTIVATE IT AND THE IRON MITE SHOULD PROVIDE ENOUGH FLOW.
DO NOT USE A SMALLER CIRCULATION PUMP TO RUN THE HEATER OR IT MAY NOT PROVIDE ENOUGH FLOW.

*********************************************************************************************************************
53600-HC CONTROL CONVERTIBLE 120 / 240 VOLTS
M-7 STYLE SYSTEM, USES SENSORS INSTEAD OF PRESSURE SWITCH
INCLUDES A 5.5 KW 240V / 1.4 KW 120V FLOW THRU HEATER

RECEPTACLE FOR 2-SPEED PUMP 120 / 240 VOLTS
RECEPTACLE FOR SINGLE SPEED PUMP 120 / 240 VOLTS
RECEPTACLE FOR BLOWER 120 / 240 VOLTS
RECEPTACLE FOR OZONATOR 120 / 240 VOLTS (MUST BE SAME VOLTAGE AS 2-SPEED PUMP)
RECEPTACLE FOR SPA LIGHT 12 V - 1 AMP

CONTROL BOX IS GRAY PLASTIC
DIMENSIONS:
HEIGHT: 10-1/2"
WIDTH: 12-5/8" (BOX ONLY)
13-1/2" (INCLUDING GROUNDING TERMINAL ON THE SIDE)
13-7/8" (OUTSIDE OF THE BOTTOM MOUNTING FEET)
DEPTH: 4-5/8" (BOX)
5" (FROM FRONT OF HEATER UNION NUT TO BACK OF CONTROL)

HEATER 15" LONG FLOW THRU STYLE (MEASURED FROM FLANGE TO FLANGE)
2-1/4" DIAMETER TUBE
UNION ENDS ARE 2" SLIP
CENTERLINE OF THE HEATER IS 2-7/8" FROM THE BOTTOM OF THE FEET

10165 ADAPTER PLATE FOR SPASIDE CONTROL
BLACK TEXTURED PLASTIC WITH PEEL OFF STICK ON GASKET ON THE BACK
OUTSIDE DIMENSIONS ARE 8-1/2" x 3-1/2"
INSIDE DIMENSIONS ARE 6-3/8" x 2-1/4"

53189 SERIAL STANDARD SPASIDE CONTROL
OUSIDE DIMENSIONS ARE 7-3/8" x 3-1/4"
USES AN 8 PIN PHONE PLUG TYPE CORD
CORD IS 7 FT LONG
BUTTONS:
BLOWER, MODE, JETS 1, JETS 2, LIGHT, WARM, COOL

10402 EXTRA SPASIDE CONTROL LABEL
USED IF THERE IS NO BLOWER TO CONTROL
SAME BUTTONS AS THE STANDARD LABEL EXCEPT THERE IS NO BLOWER BUTTON

AMP CORDS THESE ARE ALL 4 POSTION TYPE AMP CORDS, 5 FT LONG
THERE IS 1 - 4 PIN CORD FOR A 2 SPEED PUMP
THERE ARE 3 - 3 PIN CORDS FOR OTHER EQUIPMENT

LIGHT STANDARD BALBOA LIGHT HARNESS, 10 FT LONG HARNESS
INCLUDES HARNESS WITH PLUG IN TO MATCH BOX
TWIST LOCK TYPE REFLECTOR AND 12 VOLT BULB

THRU WALL FITTING IS NOT INCLUDED