AMERICAN PRODUCTS | PLUNGER ASSY, 2 VALVE | 004908

 AMERICAN PRODUCTS | PLUNGER ASSY, 2” VALVE | 004908

FILTER VALVE, PUSH PULL TYPE, SHAFT ASSEMBLY, TEMPLATE DO NOT COPY THIS TO WORD AND THEN COPY TO ENSPIRE USE NOTEPAD FOR THIS WORD ADDS FORMATTING INFO THAT DOES NOT READ PROPERLY WHEN COPIED TO ENSPIRE BE SURE TO GET ALL THE INFORMATION THAT IS LISTED ALSO PUT ANY ADDITIONAL INFORMATION AS REQUIRED START WITH A GENERAL DESCRIPTION OF THE ITEM AND WHAT IT FITS RIGHT AFTER THE PART NUMBERS ENTER THE TEXT SHOWN ALONG WITH THE HTML TAGS AS AN EXTENDED DESCRIPTION ONLY THE CHECK BOXES FOR ECLIENT AND ESHOP SHOULD BE CHECKED ALSO COPY THIS AS A MEMO ON THE ITEM THE MEMO NAME SHOULD BE THE SAME AS THE OPTIMUS ITEM NUMBER. FOR THE MANUFACTURER'S PART NUMBER, INCLUDE THE MAIN MFG PART# FOLLOWED BY ANY OTHER MFG NAMES AND NUMBER THE ITEM MAY BE KNOWN BY FIND A PART INFO (A) AND (B) WILL BE USED IN FIND A PART AS THE MAIN DIMENSIONS THE ACTUAL MEMO WILL INCLUDE EVERYTHING BELOW THIS 

 OPTIMUS # 4890-066 ANTHONY # 39960328 ANTHONY # 004908 (OLDER ANTHONY NUMBER) GENERAL DESCRIPTION: THIS IS THE COMPLETE MAIN SHAFT WITH SPACERS, TOP PLATE, AND HANDLE USED IN THE ANTHONY 2" PUSH PULL VALVE THE HANDLE IS A T-STYLE, BLACK PLASTIC, HELD ON WITH A SINGLE SET SCREW GENERAL INFO MATERIAL: SHAFT: BRASS SPACERS: BRASS TOP CAP: BRASS (INCLUDED WITH THIS ASSEMBLY) HANDLE: BLACK PLASTIC (INCLUDED WITH THIS ASSEMBLY

DIMENSIONS: LENGTH: 17-1/4" (INCLUDING HANDLE) LENGTH: 16-1/2" (A) (WITHOUT HANDLE) SHAFT DIAMETER: 1/2" (B) SPACERS: TOTAL # 2 SPACERS INCLUDED 3RD SPACER IS INCLUDED,AS PART OF THE TOP PLATE DIAMETER: 2-1/8" THICKNESS: 1/4" FROM OUTSIDE TO OUTSIDE GROOVE: 1/8" SPACING: (MEASURED ON CENTERLINE FROM FIRST SPACER WITH THE FIRST SPACER AT ZERO) 1ST 0 2ND 9" 3RD 14-3/8" SPACER O-RINGS: (3) INCLUDED THESE ARE STRETCHED ON TO THE SPACERS SO THE DIMENSIONS SHOWN ARE FOR THE ORIGINAL O-RINGS BEFORE THEY ARE STRETCHED OUTSIDE DIAMETER: 1-7/8" INSIDE DIAMETER: 1-5/8" HOLES IN SHAFT: (MEASURED ON CENTERLINE FROM THE HANDLE END OF THE SHAFT) HOLE: 3/32" AT 1-1/2" FROM END HOLE: 3/32" AT 4-5/8" FROM END

ASSEMBLY INCLUDES: SHAFT WITH 2 SPACERS TOP CAP WITH SPACER O-RING FOR EACH SPACER (3 TOTAL) SHAFT O-RING SPRING PINS (2 TOTAL) HANDLE HANDLE SET SCREW MARKINGS: THERE MAY BE MARKINGS ON THE HANDLE OR TOP CAP, SEE BELOW TOP PLATE INFO INCLUDED? INCLUDED OPTIMUS # 4890-065 ANTHONY # 39960326 ANTHONY # 017753 (OLDER ANTHONY NUMBER) GENERAL DESCRIPTION: THIS IS THE TOP PLATE USED IN THE ANTHONY 2" PUSH PULL VALVE MATERIAL: BRASS SHAPE: TRIANGLE WITH ROUNDED POINTS THERE IS A 5/16" AT EACH POINT THE HOLE CENTERLINE IS ABOUT 5/16" FROM THE EDGE

THIS TOP PLATE ALSO INCLUDES THE TOP SPACER CAST AS PART OF THE PLATE DIMENSIONS: WIDTH(CENTER TO POINT): 3" (A) TOTAL HEIGHT: 11/16" (B) CENTER HOLE DIAMETER: 1/2" INCLUDES: TOP PLATE WITH SPACER ONLY MARKINGS: "OPEN" AND "LOCK" WITH ARROWS CAST ON TOP

HANDLE INFO INCLUDED? INCLUDED OPTIMUS # 4890-048 ANTHONY # 21300913 ANTHONY # 017604 (OLDER ANTHONY NUMBER) GENERAL DESCRIPTION: THIS IS THE HANDLE USED IN THE ANTHONY 1-1/2" AND 2" PUSH PULL VALVE MATERIAL: ORIGINAL WAS CHROME PLATED BRASS THIS HANDLE IS BLACK PLASTIC SHAPE: T STYLE, WITH SET SCREW HOLE IN THE SIDE DIMENSIONS: LENGTH: 4-1/2" (A) WIDTH: 1" HEIGHT: 1-3/8" (B) INCLUDES: HANDLE ONLY MARKINGS: "ANTHONY" OR "VAL PAK" MOLDED ON THE TOP